________________________________________________________________________________________
| Home / Small Engines / Kawasaki Engines / Kawasaki FS600V |
Kawasaki FS600V Troubleshooting
| Engine Model: Kawasaki FS600V |
| Engine Type: 4-cycle V-twin cylinder OHV gasoline engine |
| Total Displacement: 36.8 cu.in (603 cc) |
| Rated Engine Power: 17 Hp (12.7 kW) |
| Carburetor Type: One-barrel, fixed main jet |
____________________________________________________________________________________
- Kawasaki FS600V Engine Specifications
- Kawasaki FS600V Engine Maintenance
- Kawasaki FS600V Engine Troubleshooting
| Engine starts hard or doesn't start |
Fuel tank is empty - Fill it up.
Incorrect fuel grade - Use correct fuel grade.
Air in fuel tank - Bleed fuel tank.
Damaged spark plug wiring connection - Inspect the spark plug wire connection, replace or repair.
Spark plug is faulty - Change spark plug as required.
Plugged fuel filter - Install new filter.
Safety contact for brake pedal defective - Install new part.
Incorrect carburetor adjustment - Adjust carburetor idle mixture screw.
Poor compression - Inspect and replace wear parts.
Damaged or not adjusted choke cable - Adjust properly or change the cable.
| Irregular engine running |
Air intake screen is blocked - Need to wash or clean.
Defective ignition system - Check ignition system and replace faulty parts.
Choke cable is faulty or stuck - Clean or change the cable.
Air filter element is plugged - Change or service air filter.
Fuel pump is dirty or defective - Test fuel pump and change if necessary.
| Engine starts and stops immediately |
Damaged spark plug - Replace spark plug.
Faulty or dirty carburetor - Service or change carburetor.
Ignition coil is faulty - Replace ignition coil as necessary.
Loose or worn valve springs - New valve springs need to be installed.
Valves are stuck - Clean the valves.
| Engine keeps overheating |
Engine oil insufficient - Fill the crankcase with engine oil.
Engine is under excessive load - Reduce engine load.
Cooling fins are blocked - Clean and wash as required.
Too lean carburetor mixture - Make the correct settings.
Improper ignition timing - Ignition timing needs to be set properly.
Improper valve setting - Adjust valves as required.
| Engine knocking sound or abnormal noise |
Stale gasoline - Use proper gasoline.
Engine overload - Reduce engine load.
Engine oil level is low - Need to add engine oil.
Low idle speed setting is incorrect - Adjustment required.
Dirty or defective fuel pump - Service or replace fuel pump.
Main bearings or crankshaft wear - Change or repair worn components.
Valve clearance is improper - Adjust to proper valve clearance.
Worn piston rings or cylinder bore - Change faulty parts.
| Engine loses power |
Dirty or improperly adjusted carburetor - Adjust the carburetor correctly or clean it.
Air filter element is plugged - Replace or clean air filter.
Clogged or damaged fuel pump - Service or replace fuel pump.
Ignition system problems - Check ignition and replace faulty components.
Cylinder head gasket is defective - Change cylinder head gasket.
Burned or stuck valves - Clean or replace valves.
Push rod is worn or damaged - Push rod needs to be changed.
Cylinder block components are faulty - Defective components need to be replaced.
Plugged oil filter (if equipped) - Service or replace oil filter.
| Excessive fuel consumption |
Throttle did not open fully - Replace or adjust throttle cable.
Carburetor main jet adjustment is incorrect - Adjust the carburetor main jet correctly.
Defective or loose spark plug - Re-tighten or replace spark plug.
Stuck, burned, or worn valves - Service or replace valves.
Worn sleeve, rings, or piston - Replace defective parts as required.
Incorrect valve clearance - Adjust to proper valve clearance.
| Excessive oil consumption |
Gaskets or seals can be faulty - New components need to be installed.
Valve stems and guides are worn - Valves must be replaced.
Damaged or seized piston rings - Piston rings need to be replaced.
Damaged cylinder liner or piston - Inspect liner and piston, replace as necessary.
Clogged breather hose or pipe - Replace or clean.
________________________________________________________________________________________
________________________________________________________________________________________
| Engines Technical Specifications |