Home / Lawn and Garden Tractors / Husqvarna Lawn Tractors / Husqvarna TS354XD

Husqvarna TS354XD Troubleshooting

The Husqvarna TS354XD garden tractor was manufactured from 2017. The Husqvarna TS354XD is powered by Kawasaki FR730V 4-cycle vertical shaft V-twin cylinder air-cooled gasoline engine with a max output power of 24 hp (18 kW) and 53.8 Nm (39.7 lb-ft) of peak torque at 2400 rpm.

The engine has an internally vented carburetor with fuel shut-off solenoid, full pressure lubrication system with spin-on oil filter, and electronic spark ignition system. The Husqvarna TS354XD is fitted with a Tuff Torq K66 belt-driven hydrostatic transmission with a foot-controlled variable speed drive.

The maximum forward speed - 5.6 mph (8.9 km/h), maximum reverse speed - 2.5 mph (4 km/h). The Husqvarna TS354XD garden tractor is fitted with 16x6.50-8 front tires and 23x10.5-12 rear tires. The wheelbase is 48" (1215 mm). The tractor is compatible with a 54" mid-mount side discharge high-lift blade mower deck with a cutting height of 1.5-4.0" (38-100 mm), and spring-assisted cutting height adjustment.

Engine Troubleshooting
Engine doesn't start or hard to start
Gas tank is empty - Fill it up
Wrong fuel grade - Use quality gasoline
Fuel system clogged - Repair or replace
Spark plug wire is disconnected or loose - Inspect the spark plug wire connection, replace or repair
Spark plug is faulty - Spark plug need to be replaced
Fuel filter is plugged - Fuel filter needs to be replaced
Faulty safety switch - Change damaged switch
Problems with carburetor adjustment - Adjust as required
Low engine compression - Inspect cylinder block and change defective components
Choke cable is unadjusted or damaged - Adjust properly or change the cable
Engine runs roughly
Air intake screen is blocked - Need to clean or wash
Ignition system is defective - Inspect ignition system and change failed components
Throttle cable is stuck or faulty - Change or service the cable
Air filter is blocked - Service or replace air filter
Fuel pump is dirty or defective - Clean or change fuel pump
Engine starts and stalls immediately
Damaged spark plug - Spark plug need to be replaced
Clogged or defective carburetor - Service or change carburetor
Ignition coil is faulty - Change ignition coil as required
Weak or damaged valve springs - Change valve springs
Valves sticking - Valves must be cleaned
Engine overheats
Engine oil level is insufficient - Need to add engine oil
Engine is overloaded - Load reducing required
Cooling fins are blocked - Need to wash or clean
Carburetor mixture is too lean - Set the carburetor properly
Incorrect ignition timing - Set the ignition timing correctly
Improper valve setting - Set the valves properly
Engine knocking or noise
Stale gasoline - Change fuel
Engine is overloaded - Load reducing is recommended
Low engine oil level - Add oil to the engine crankcase
Incorrectly set low idle speed - Correct idle settings
Fuel pump is defective or dirty - Clean or change fuel pump
Crankshaft or main bearings failure - Repair or replace defective parts
Valve clearance is incorrect - Adjust valve clearance according to specifications
Piston rings or cylinder bore are damaged - Change faulty parts
Lack of engine power
Carburetor is improperly adjusted or clogged - Clean or properly adjust carburetor
Clogged air filter - Change or service air filter
Fuel pump is dirty or defective - Service or replace fuel pump
Ignition system is defective - Check ignition and replace faulty components
Defective cylinder head gasket - Install new head gasket
Valves are burned or stuck - Clean or replace valves
Push rod is worn or defective - Push rod needs to be changed
Faulty cylinder block components - Defective parts need to be replaced
Engine using too much gasoline
Choke didn't open fully - Adjust or change choke cable
Improper adjustment of carburetor main jet - Adjust the carburetor main jet correctly
Loose or faulty spark plug - Tighten or replace spark plug
Valves are stuck, worn, or burned - Change or clean valves
Piston, sleeve, or rings are damaged - Change faulty components
Valve clearance is wrong - Check and adjust
Excessive engine oil consumption
Damaged seals or gaskets - Install new components
Damaged valve guides or valve stems - Valves replacement required
Stuck or defective piston rings - Replace piston rings
Damaged cylinder liner or piston - Check liner and piston, change as required
Blocked breather hose or pipe - Clean or change

Hydrostatic Transmission Troubleshooting
HST transmission noises
Bent or unadjusted speed control pedal linkage - Adjust or change linkage
Transmission overload - Reduce transmission load
Transmission fluid is dirty or fluid level is too low - Top up to proper level or change transmission fluid
Transmission parts are worm or defective - Replace or repair defective components
Shifting is hard
Loose or broken shift linkage - Change defective linkage
Seized or worn hydrostatic pump - Replace or repair pump
Transmission shift control components are defective or misadjusted - Replace or adjust as required
Loss of power
Transmission oil level is low - Check transmission oil level and add oil as required
Drive pulley is worn or faulty - Replace pulley
Shifter linkage is not adjusted or faulty - Adjust properly or replace linkage
Worn or unadjusted speed control linkage - Adjust or change linkage
Transmission leaking
Broken transmission gaskets or seals - Seals and gaskets need to be replaced
Final drive shaft leaks - Change shaft seals
Cracked transmission housing - Replace housing or transmission assembly

Mower Deck Troubleshooting
Mower vibrates excessively
Clogged or damaged mower drive sheave - Clean or replace sheave
Drive belt is defective or loose - Adjust belt tension or change the belt
Bent or unbalanced mower blades - Balance or replace blades
Blade bolts are not tightened well - Tighten bolts as required
Discharge chute regular clogging
Mowing speed is too high - Select a slower speed
Grass is too long - Adjust mower to lower cutting height
Engine rpm is too low - Open choke fully
Cutting level is too low - Use a higher cutting height
Drive belt installed improperly - Drive belt must be installed correctly
Lawn mower leaving uncut grass
Deck is plugged with grass - Mower deck needs to be cleaned
Excessive blade dullness - Sharpen the blades
Defective or worn blades - Blades must be changed
Fast mowing speed - Select a slower speed
Cutting level is too low - Use correct cutting height
Grass bag is full - Grass bag must be empty
Blade scalped grass
Uneven or bumpy lawn - Lawn leveling required
Mower deck cutting height is set too low - Use correct cutting height
High ground speed - Need to slow down
Improperly leveled mower deck - Deck should be adjusted correctly
Worn or bent blades - Change the blades
Low tire inflation - Inflate tires as required
Mower cuts uneven
Tires are not properly inflated - Need to inflate tires
Deck level is not correct - Level the deck correctly
Blades are excessively dull - Need a blade sharpening
Damaged or worn blades - Change the blades
Cutting deck clogging - Clean out the mower deck
Broken mower deck shell - Repair or replace the deck
Mower spindle is loose or defective - Replace or repair the spindle

Electrical Troubleshooting
Battery cannot be charged
Corroded or loose cable connections - Service or tighten connections
Battery terminal connectors are faulty - Terminal connectors need to be changed
Defective battery - Battery replacement required
Starter motor cranks slow
Low battery power - Battery needs to be recharged
Battery is draining quickly - Service or change the battery
Wires are disconnected or battery terminals are corroded - Connect wiring properly or install new terminals
Starter motor is not working
Battery is discharged or worn - Recharge or replace battery
Battery wires are disconnected or incorrectly connected - Check wires and connect correctly
Battery capacity is low - Recharge the battery
Incorrectly gapped or worn spark plug - Clean, gap or change spark plug
Starter motor or solenoid is damaged - Repair starter or replace solenoid



Lawn and Garden Tractors Technical Specs